Nema 23 stepper motor 23HS9442. Nema 23 stepper driver DM542A. DM542A is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 18VDC to 50VDC.
It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, what's more, the positioning accuracy is also higher.It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on. Average current control, 2-phase sinusoidal output current drive. Supply voltage from 18VDC to 50VDC. Overvoltage, under voltage, overcorrect, phase short circuit protection.
15 channels subdivision and automatic idle-current reduction. 8 channels output phase current setting. Motor torque is related with speed, but not related with step/revolution. High hording torque under high speed.No condensation, no water droplets. Prohibition of combustible gases and conductive dust. Pulse signal, PUL+ is the positive end of pulses input pin.
PUL- is the negative end of pulse input pin. DIR signal: DIR+ is the positive end of direction input pin. DIR- is the negative end of direction input pin. Enable signal: ENBL+ is the positive end of direction input pin.
This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver.ENBL- is the negative end of direction input pin. PC's control signals can be active in high and low electrical level. When the high electrical level is active, all control negative signals will be connected together to GND. When low electrical level is active, all control positive signals will be connected together to public port.
Now give two examples(Open collector &PNP), please check them. Input port circuit (Yang connection).
2 Input port circuit (Yin connection). R must connect in the control signal part. Function choice (Using DIP pins to achieve this function). 1 Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table. SW4 is used for this purpose.
OFF meaning that the standstill current is set to be half of the selected dynamic. Current and ON meaning that standstill is set to be the same as the selected dynamic current.
The first three bits (SW 1, 2, 3)of the DIP switch are used to set the dynamic current. Closest to your motor's required current.
Semi-flow function is that there is not step pulse after200 ms, the driver output current automatically. Reduced to 40% of rated output current, which is used to prevent motor heat.
Pins of motor & power. The peak input current can not up to 6A. To have 20mm of space around, cannot be placed next to other heating devices.S more, avoid dust, oil mist, corrosive gas, heavy humidity and high vibration. 1, the status on light? PWR: green, normal work light. ALM: red, failure light, the motor with phase short-circuit, overvoltage and under-voltage protection. Motor doesn't run, without holding torque.
Wrong connection of stepper motor. RESET signal is effective when offline. Motor doesn't run, butmaintains holding torque. Adjust PMW & signal level.
Change connection for any of 2 wires. Motor's holding torque is too small. Too small relative to current setting.Driver does not match with the motor. P2 P3 is set to X-axis for the X-axis pulse. P4 P5 is set to Y-axis, Y axis pulse. P6 P7 is set to Z-axis Z-axis pulse. The other can be set to A B C axis.
A-axis pulse P8 P9 is set as the A axis. P14 is set to B-axis B-axis pulse P1.
P16 P17 is set to C-axis, C axis pulse. Can also be set to the spindle control signal \ electrical permit. Input interface for the P10 P11 P12 P13 P15.
Built in DB25 male connector. DB25 Output Pin:P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. DB25 Input Pin: P10, P11, P12, P13, P15. High quality with Surface-mount Tech. If you not receive goods for a long time, you search the tracking on Yodel website.
If the tracking has problem, you make a call to your local Yodel, then contact me. Service: If you need more pictures, descriptions, manual, please contact me. If you have problem, when you connect it, you contact me, I will help you.
Whats more, our products are mainly used in CNC machine, Carver machine, Automazation, Printer, Stage lighting and so on. If you have any questions about our products, please dont hesitate to contact me. And I will try my best to support you. This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Electric Motors\Stepper Motors". The seller is "longsmotor-yy" and is located in this country: GB.
This item can be shipped to United Kingdom.